Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2 Manuale Utente Pagina 104
- Pagina / 182
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Maintenance and diagnostics
4-8 MicroEDGE Pro Instruction Manual 807290
I/O test
Conduct this test if:
• An I/O point is malfunctioning.
• You need to eliminate CNC I/O operation as a problem in the system.
• A continuous fault is occurring, such as a limit switch that is not turning on or clearing.
To test I/O:
1. On the Machine Interface screen, choose the I/O port you want to test.
2. Follow the instructions on the screen to connect the Picopath (white) or HyPath (green) test plug into the I/O port
you selected on the back of the MicroEDGE Pro.
3. On the Machine Interface screen, press Test. A message informs you if the test is successful.
4. If the test fails, follow the instructions on the screen to connect the second Picopath (orange) or HyPath (red) test
plug to isolate the I/O point that is causing the problem.
- MicroEDGE 1
- MicroEDGE Pro 3
- Shape cutting control 3
- CONTENTS 5
- Table of ConTenTs 10
- Hypertherm S-1 11
- In this section: 11
- ELECTRICAL HAZARDS 12
- RECOGNIZE SAFETY 12
- INFORMATION 12
- FOLLOW SAFETY 12
- INSTRUCTIONS 12
- ELECTRIC SHOCK CAN KILL 13
- Hypertherm S-5 15
- S-6 Hypertherm 16
- Hypertherm S-7 17
- Instant-on torches 17
- NOISE CAN DAMAGE HEARING 18
- Hypertherm S-9 19
- LASER RADIATION 20
- ADDITIONAL SAFETY INFORMATION 21
- WARNING LABELS 21
- S-12 Hypertherm 22
- Symbols and Marks 23
- Product Stewardship 25
- Product Stewardship PS-3 27
- PRODUCT sTewaRDshiP 27
- Higher-level systems 27
- PS-4 Product Stewardship 28
- Environmental Stewardship 29
- Methods of reducing emissions 31
- Installation and use 31
- Assessment of area 31
- Cutting cables 32
- Equipotential bonding 32
- Earthing of the workpiece 32
- Screening and shielding 32
- Attention 33
- WARRANTY 33
- W-2 Compliance Information 34
- Section 1 35
- SPECIFICATIONS 35
- SpecificationS 36
- Cutting table 37
- Overview of MicroEDGE Pro 39
- Rear panel 40
- System specifications 41
- HyPath configuration 42
- Picopath configuration 43
- SERCOS II configuration 44
- SERCOS III configuration 45
- Integrated Sensor THC 46
- Interior temperature 47
- Air circulation 47
- AC input 47
- Section 2 49
- INSTALLATION 49
- InstallatIon 50
- Upon receipt 51
- Installation requirements 51
- Mounting the CNC 52
- X and Y axis configuration 53
- AC power 54
- Chassis grounding 55
- Interface ports 56
- Picopath connections 57
- Picopath I/O connector 58
- Encoder jumper options 62
- HyPath connections 65
- HyPath inputs 66
- HyPath outputs 68
- HyPath I/O connectors 71
- Analog connections 75
- THC cable specifications 76
- SERCOS II I/O configuration 79
- SERCOS III I/O configuration 80
- Serial port configuration 81
- Remote on/off cable 83
- Wireless network card 84
- Mapping a network drive 86
- Adding a folder in Phoenix 87
- Section 3 89
- OPERATION 89
- Operating the CNC 90
- OperatiOn 91
- Screen navigation 91
- View additional manuals 92
- Automated operations 93
- CutPro Wizard 94
- PC keyboard 94
- Updating Phoenix software 95
- Updating the cut charts 96
- Section 4 97
- MAINTENANCE AND DIAGNOSTICS 97
- Diagnostic tests 100
- Maintenance and diagnostics 101
- Serial test 102
- USB test 103
- I/O test 104
- Axis test 106
- WARNING! 106
- THC test 107
- LAN and Hypernet tests 108
- Joystick and speedpot test 109
- Troubleshooting 110
- Wireless troubleshooting 119
- HyPath 24 I/O board (141070) 121
- Motherboard (141110) 123
- Analog board (141125) 130
- Section 5 149
- PARTS LIST 149
- Common MicroEDGE Pro parts 150
- Picopath MicroEDGE Pro parts 152
- HyPath MicroEDGE Pro parts 153
- Parts List 154
- Common test plugs 155
- Picopath test plugs 156
- HyPath test plugs 157
- Cable connector kits 158
- Section 6 159
- WIRING DIAGRAMS 159
- Introduction 159
- Wiring diagram symbols 159
- Wiring Diagrams 160
- Torch Symbols 161
- SHEET 1 OF 20 163
- MICROEDGE PRO CNC 163
- SHEET 2 OF 20 164
- MICROEDGE PRO CNC 164
- WITH HYPATH INTERFACE 164
- SHEET 3 OF 20 165
- WITH SERCOS II INTERFACE 165
- SHEET 4 OF 20 166
- MOTHERBOARD PCB 166
- SHEET 5 OF 20 167
- POWER DISTRIBUTION PCB 167
- SHEET 6 OF 20 168
- MICROEDGE PRO REAR 169
- SHEET 8 OF 20 170
- ATX POWER SUPPLY 170
- Joystick_LEFT 21 171
- Speed_Pot1+ 23 171
- Speed_Pot1- 24 171
- Speed_Pot2+ 25 171
- Speed_Pot2- 26 171
- THC2_Nozzle_Contact_Sense+ 10 172
- Joystick_DOWN 20 172
- J1 I/O 1-24 173
- J2 DRIVE/ENCODER 173
- /RXD_INB 13 174
- SHEET 13 OF 20 175
- PICOPATH 4-AXIS INTERFACE 175
- SHEET 14 OF 20 176
- HYPATH I/O INTERFACE PCB 176
- SHEET 15 OF 20 177
- HYPATH 4-AXIS SERVO PCB 177
- SHEET 17 OF 20 179
- PICOPATH 2-AXIS INTERFACE PCB 179
- SHEET 19 OF 20 181
- PICOPATH 2-AXIS MCC PCB 181
- SHEET 20 OF 20 182
- WITH SERCOS III INTERFACE 182
Prodotti e manuali riguardandi Apparecchiature Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2
(184 pagine)
(152 pagine)
(184 pagine)
(152 pagine)
Apparecchiature Hypertherm D845GEBV2 Manuale Utente
(128 pagine)
(128 pagine)
Apparecchiature Hypertherm HRT2 Manuale Utente
(64 pagine)
(64 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale